We had an old hard water treatment system that was broken. Tap water from this old system gave me a headache, so we bought bottled water. I had to buy about 10 gallons a week, or about $ 10.00 a week, more than € 500.00 per year. I looked at the existing literature and, above all, the three systems, which provide drinking water for approximately 9.7 cents per gallon was $ 1.00 VRS.
After studying each of these systems, we decided to go with a whole house water treatment AquasanaSystem. I have a DIY installation of water treatment project in the garage, where the old water softener to be used. This method of treatment of the water is filtered water for our baths, showers, washing dishes and clothes.
This hard water treatment system does not use salt to condition the water. It 'can filter 300,000 gallons of water before it should be changed. I have a water meter in line to the system that appears to 9,999,999 liters of gallons of water, to determinethe amount of water we are using.
We have added a premium Aquasana Under Counter water filters for drinking water treatment plant under the kitchen sink to clean drinking water. This filter extracts the pollutants by up to 0.995%. This is equivalent to or higher than the water bottle and not buy a headache from drinking this water.
I installed a tap on our special porcelain sink in the kitchen to the filtered water. I drilled a hole in the porcelain sink mount, the tap water.This is a difficult task and must be done very carefully. If you feel you need to hear even then a plumber.
I studied the advice and recommend tools such as porcelain drill. You can use a special set of points, only very expensive to drill holes in porcelain. I decided to make my own mask drill 5 / 8 "hole for the tap again. I bought two brass washers, has the largest 3 / 4" inside diameter, which I attached to the sink with a rubber adhesive onSpace for the new faucet.
Let the glue dry for 10 minutes or more and then use a Dremel with a cutting edge path through the porcelain of the "wheel 3 / 4 back to bare metal. This is a very difficult process because you do not want fresh, crack or porcelain chip under the brass washer. Keep your work area with water in the drill brass washer while it is necessary to maintain the temperature of the drill and brass washer.
The second step is to insert a 3 / 4 "out(OD) and a 1 / 4 "inside diameter (ID) brass washer at the center of the brass washer others. You also need a 1 / 4" OD and 1 / 16 "ID spacer small space inside the brass washer . This gives you the right to the center tap. Use the Dremel with a cutting edge back to a pilot hole through the center of the spacers and through the porcelain drill down to the metal.
The third step is to remove the spacer washer and allow blocked but the brass brass washer big for the sink.There is a heat sink under the porcelain. Now drill a 1 / 4 "starter hole through the porcelain and metal sinks to the point marked above.
The fourth step is to take a 5 / 8 "hole saw carbide drill and practice a meticulously 5 / 8" hole in the sink. Be sure to adjust the saw drill hole in the center of the large brass plate with a good distance from the disk. Use a low speed drill and drill to keep the water in this sink hole and to keep everything below the boiling pointWater.
After the completion of the hole to break a small hammer and a screwdriver and gently tap brass washer, being careful not to on the porcelain sink. Porcelain is very unforgiving and difficult to resolve. Remove excess glue from the sink, use a clean hole in the sink with no chips or cracks in the ceramic. The valve cover should cover the cracks. You can your new faucet to the sink to be mounted.
Fix the pipes to the new faucetfinal step in the filter manufacturer's instructions. Turn on the water and look for leaks. Tighten each intersection, the leaks. Let the water through the filter according to manufacturer's instructions are executed. Now you can test the taste of their own treatment system Award Aquasana filtered water.
0 comments:
Post a Comment